manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 75

Inserting and Extracting a MIC

Servicing the Hardware

6-3

Figure 6-1

Inserting a MIC

Extract a MIC

The following procedure is referenced in the removal procedures for specific MICs; to ensure correct 
removal, perform the removal procedure for the specific MIC, including all steps prior to and after the 
actual MIC extraction. Perform the following steps to extract a MIC; see Figure 6-2:

1. Put on an antistatic wrist strap (one is shipped with the system), and attach it to an appropriate grounded 

surface.

2. Using a Phillips screwdriver, loosen the captive screws on the front panel of the MIC being removed.

3. Holding the MIC handle and keeping it perpendicular to the slot, pull gently on the MIC to disengage 

it from the circuit board.

4. Keeping the MIC horizontally level, carefully slide the MIC out of the chassis, and place it in an 

antistatic bag.

Note

Do not attach the wrist strap to a painted surface; there is an ESD convenience jack located on 
the front of the chassis.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды