Record system 20 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

34/ 56

→ AKA

The output signal indicates that a triggering signal on the outer
side of the door is active.
▪ The output switches independently of the current operating

mode.

→ ZLP-1

Additional printed circuit board to connect conventional safety
light barriers. Once identified, a ZLP-ELS (automatic recogni-
tion) can only be reset with the FPC.

→ Without

X No additional p.c.b. is connected.

→ ELS

Additional p.c.b. for 2 ELS is connected.

→ ZLP-2 (only RED)

Additional p.c.b. for RED installations with non-record sensors.
Once identified, a ZLP-AKI (automatic recognition) can only be
reset manually with the FPC.

→ Without

X No additional p.c.b. is connected.

→ AKI

Additional p.c.b. is connected for AKI on RED installations.

INPUT/OUTPUT → FEM0

→ AUX2_IN
→ AUX3_IN

Configurable input signals on FEM0 (terminals 53 and 57).
▪ For further instructions about every signal, see also

Pa-

rameter → Input/Output → STG → AUX0_IN

→ Disabled

X

→ SURV

Selection of

Locked

operating mode with clock timer.

0V/open =

Locked

operating mode

24V = back to previous operating mode

→ Continuously open

Selection of

Continuously open

operating mode with pulse

button.
1st pulse (24V 0V/open) =

Continuously open

operating mode

2nd pulse (24V 0V/open) = back to previous mode

→ SIS

Safety signal in closing direction.
0V/open = security active
24V = security passive

→ SIO

Safety signal in opening direction.
0V/open = security active
24V = security passive

→ AKI button reduced

(not with RED)

Opening to reduced opening width with pulse signal (0V/open -
> 24V). The signal is intended for connecting a button on the
inner side of the door.

«
...
32
33
34
35
36
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Бренд: Yale Страницы: 72

Бренд: Bartec Страницы: 46

Бренд: ESAB Страницы: 44

Бренд: Thermal Arc Страницы: 56

Бренд: INNO Instrument Страницы: 45

Бренд: Thermal Dynamics Страницы: 40

Bench Glo-Ring AH2711

Бренд: Eraser Страницы: 4

Бренд: gala gar Страницы: 28

Бренд: Dometic Страницы: 24

Бренд: Tokentools Страницы: 29

Бренд: TEAMWELDER Страницы: 64

Бренд: Saf-Fro Страницы: 157

Бренд: Chicago Electric Страницы: 32

Бренд: Pamex Страницы: 2

Бренд: Pamex Страницы: 3

TS 5000 L-E-ISM VPK

Бренд: GEZE Страницы: 28

REDI-MIG 325 Remote

Бренд: Lincoln Electric Страницы: 40

RANGER 9 IM753-A

Бренд: Lincoln Electric Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды