Record system 20 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

39/ 56

→ AUX13_IN

Configurable input signal for FEM1
Connector J1, terminals 70 and 71 (only FEM1)
Floating, optically disconnected 24V input

→ Disabled

X

→ AUX10_OUT … AUX1D_OUT

14 configurable output signals for FEM1.
Connector J2, floating change over contact 30 volt DC / 1 A
Normally closed (NC) or normally open (NO) contact (selection
via jumper position --> basic position = NO contact).

→ Inactive

X

→ Alarm output

This output signal indicates severe breakdowns.
Relay passive = breakdown
Relay active = no breakdown

→ Locked

This output signal shows whether the door is locked.
Relay passive = door not locked
Relay active = door closed and locked

→ Closed

This output signal shows whether the door is closed.
Relay passive = door not closed
Relay active = door closed
▪ The output may switch with a slight delay, i.e. when closing

only after the pressing phase and, when opening by hand,

not before the door has opened up to approx. 10 mm.

→ Open

This output signal shows whether the door is open.
Relay passive = door not open
Relay active = door has opened up to opening width
▪ The output may connect with a slight delay, i.e. when

opening not before the end stop has been recognised and,

when closing by hand, not before the door has been pulled

closed approx. 30 mm.

→ AKI

This output signal shows that a triggering signal on the inner
side of the door is active.
▪ The output connects independently of the current operating

mode.

→ AKA

This output signal indicates that a triggering signal on the outer
side of the door is active.
▪ The output connects independently of the current operating

mode.

«
...
37
38
39
40
41
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Pulse-Expert M-400S

Бренд: Masterweld Страницы: 25

Бренд: HySecurity Страницы: 8

Fusion splicer 232103

Бренд: Televes Страницы: 24

Бренд: Elettro CF Страницы: 24

Бренд: Ultrasonic Страницы: 16

SATO-115E5 Series

Бренд: AXXAIR Страницы: 60

Бренд: Dormakaba Страницы: 12

Бренд: AOTAI Страницы: 32

Бренд: Matco Tools Страницы: 18

Бренд: KROME Страницы: 2

Бренд: PDQ Страницы: 3

Бренд: Riland Страницы: 14

Evolution TS320ACDC

Бренд: SifWeld Страницы: 28

Бренд: SifWeld Страницы: 33

Бренд: R-Tech Страницы: 18

Бренд: quiko Страницы: 20

Бренд: Daihen Страницы: 35

Бренд: Far Tools Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды