Record system 20 Скачать руководство пользователя страница 17

Страница: 17 / 57

Parameter explanations V2.1_V2.6

IRA_B8_EN_2V2_REC_102-020401137

17/ 56

Input/Output → STG →
SÖK:NSK → Speed

Miscellaneous → Alarm display
→ Time activation

→ CO48 Sandow direct

Door with integrated rubber cord (power storage).
▪ For 108/150 mm drives

▪ Only for motors with brake

▪ In France no batteries are allowed

▪ Default parameters:
Parameter

Default value

Driving cycle → Close → Hold-
ing force

Drive → Brake

Open/Close-Position

Drive → Power failure

Emergency operation

Input/Output → STG →
AUX1_IN

Broken rubber cord

→ Basic escape route

Escape route door for GB with special battery surveillance.
▪ Only allowed with lead-acid battery (British standard).

▪ With

Parameter → Battery Emergency operation

only set-

tings in opening direction are possible.

▪ Battery operation cannot be configured, after a power fail-

ure an emergency opening always occurs according to pa-

rameter

Battery emergency operation

. Once mains voltage

is back, it changes automatically back to the previous op-

erating mode.

▪ The battery is tested once per minute. Should the battery

be defective or insufficiently charged, an emergency open-

ing according to

Parameter → EmergOp Battery

is carried

out, even in case of available mains voltage. Returning to
normal operation is only possible with a new start via

EMERGENCY STOP or FPC902.

▪ Default parameters:
Parameter

Default value

Drive → Power failure

Emergency operation

Drive → Battery

Lead

→ Folding door Australia

Folding door for Australia with special driving behaviours.
▪ Different driving behaviours

▪ Higher opening and closing speed
▪ In some ways different behaviour after stop and collision

Содержание system 20


























































Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды

Record system 20, Перевод оригинального руководства

Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды