Record system 20 Скачать руководство пользователя страница 20

Страница: 20 / 57

Parameter explanations V2.1_V2.6

IRA_B8_EN_2V2_REC_102-020401137

20/ 56

→ 3 buttons

Door controlled by three keys – a key to open, a key to close
and a key to stop the door.
▪ One pulse 0V 24V with the AKI button opens the door up

to the opening width.

▪ To close the door, the button CLOSING DEAD MAN must

be maintained pressed (24V).

▪ The stop button is connected to the SIO input. Conse-

quently, the door can only be stopped in opening direction.

▪ If several keys are pressed at the same time the door

stops.

▪ A locked door can only be opened by SSK. The SSK also

has a

Dead man

function. The CLOSING button closes

and locks the door again.

▪ In

Continuously open

operating mode the door opens au-

tomatically.

▪ Default parameters:
Parameter

Default value

Input/Output → STG →
AUX0_IN

AKI BUTTON

Input/Output → STG →
AUX1_IN

CLOSING DEAD MAN

Input/Output → FEM0 →
AUX2_IN

SIO

Input/Output → SIO → Function
SIO

Stop

Input/Output → EMERG. STOP
Reset

Disabled

→ Default 1

For special doors for a major customer of RTW

Parameter

Default value

Driving cycle → Closing speed 40

Driving cycle → Opening speed 40

Driving cycle → Close → Creep
section

Driving cycle → Close → Hold-
ing force

Driving cycle → Open → Accel-
eration

Driving cycle → Open → Decel-
eration

Содержание system 20


























































Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды

Record system 20, Перевод оригинального руководства

Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды