Record system 20 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

15/ 56

→ RED battery

X Standard setting for escape route doors.

▪ This door type can only be selected for redundant control

units with appropriate software.

▪ Standard and emergency channels are checked at least

every 24 hours for correct functioning. Normally, the re-
dundancy test occurs after approx. 22 to 23.5 hours on an

open door with a special door movement. If the door re-

mains open for more than 23.5 hours the test can also take

place in closed position.

▪ Triggering sensors in escape direction (AKI) must also be

redundant. At every door opening triggered by those sen-
sors, time data are controlled on the escape route door.

→ RED door closed

Variant for escape route doors, with which the redundancy test
can only be carried out in closed position.
▪ Attention: such a configuration does not necessarily com-

ply with the norm requirements.

CO48 Ventouse

Door with mechanical power storage device. A rubber cord is
fixed to an onboard carriage. The carriage is maintained in
closed position by a magnet to relieve the drive. A switch indi-
cates any break of the rubber cord.
▪ Possible with drive height 200 mm.

▪ Default parameters:
Parameter

Default value

Drive Power failure

Emergency operation

Input/Output STG AUX1_IN

Broken rubber cord

TOS

For doors with swivelling door leaf. The swivelling movement is
monitored with a switch connected at the Emergency stop
input. Optionally, mechanical locking devices operated by
hand can be mounted on the door leaf.
▪ Manual locking devices are connected to inputs AUX2_IN

and AUX3_IN of function extension module FEM0
(0V/open = manual locking open). The appropriate param-

eter must be configured manually to the signals TOS_DV1

and TOS_DV2.

▪ So that anti-burglary protection is guaranteed, manual

locking devices must be closed in the operating mode

Locked

. Otherwise, error 29 is raised.

▪ If operating mode

Locked

has not been selected the man-

ual locking devices must be open. Otherwise, the door

stops and error 30 is raised.

▪ The SSK function is ensured.

«
...
13
14
15
16
17
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Бренд: quadient Страницы: 5

DIGITIG 200DC MULTIPRO

Бренд: Sherman digitec Страницы: 18

Бренд: Oerlikon Страницы: 140

iWeld 900 Series

Бренд: LaserStar Страницы: 172

Бренд: Thermrup Страницы: 12

Бренд: XTline Страницы: 32

Бренд: ESAB Страницы: 20

Бренд: Unimig Страницы: 16

102-020.110.805

Бренд: Record Страницы: 14

Bermuda Inset 3 BS Super

Бренд: Baxi Страницы: 24

Бренд: BFT Страницы: 24

Electron MultiSpot M25 AL

Бренд: CHIEF Страницы: 28

Бренд: CornellCookson Страницы: 33

Бренд: FlexiForce Страницы: 17

Бренд: gala gar Страницы: 40

Бренд: gala gar Страницы: 69

Бренд: PERKEO Страницы: 10

Бренд: Jasic Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды