Record system 20 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

8/ 56

Seal

0 Setting for doors with special wide and strong seal in the clos-

ing area, e.g. for OP doors.
0 = no seal
1 = 10 cm wide sealing area
… = approx. 0.5 mm increments
40 = 30 mm wide sealing area
▪ With the sealing area collision surveillance is reduced dur-

ing the closing phase! The sealing area should therefore

only be used for the smallest necessary distance.

▪ The sealing width setting refers to the door travel meas-

ured at the belt.

▪ During the learning cycle, the closed position is reached or

sought with increased force.

TIME DELAY OPEN

Time delay open

0 Determines the minimum time during which a door stays open

after it has been opened by a triggering signal of type AKA or
AKI:
0..20 = 0 to 20 seconds, 1 s increments
21..40 = 22 to 60 seconds, 2 s increments
▪ Time delay open only starts after all triggering and safety

signals in closing direction have disappeared.

▪ With OP doors, this parameter determines the hold-open

time in case of reduced opening width.

Time delay SSK

4 Determines the minimum time during which a door stays open

after it has been opened by a triggering signal of type SSK.
0..20 = 0 to 20 seconds, 1 s increments
21..40 = 22 to 60 seconds, 2 s increments
▪ Time delay open only starts after all triggering and safety

signals in closing direction have disappeared.

With OP doors, this parameter determines the hold-open time
in case of total opening width.

SSK delay

0 Delay before the door starts opening after an SSK signal.

0 = no delay
… = 0.2 s increments
40 = 8 seconds delay
▪ The SSK signal is only delayed if the door is closed.

«
...
6
7
8
9
10
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

weldmatic 350i CP139-2

Бренд: WIA Страницы: 28

Бренд: Eco Страницы: 10

Бренд: Abicor Binzel Страницы: 2

Бренд: Paton Страницы: 35

Бренд: Manaras Страницы: 28

BI-WELDER TIG 2040 DC-HF

Бренд: Cebora Страницы: 11

Бренд: EWM Страницы: 54

Бренд: Sesamo Страницы: 4

3VL9800-3A 0 Series

Бренд: Siemens Страницы: 7

Cutter Inverter 20

Бренд: GYS Страницы: 20

Бренд: GYS Страницы: 40

POWERDUCTION 50LG

Бренд: GYS Страницы: 72

Бренд: GYS Страницы: 80

Бренд: GWS Страницы: 18

Бренд: Parkside Страницы: 37

Бренд: Euro-Line Страницы: 28

WeldCloud Mobile

Бренд: ESAB Страницы: 18

Бренд: WIELANDER+SCHILL Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды