Record system 20 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

12/ 56

Two motors

This parameter indicates whether one or two motors are con-
nected to the STM. Normally, the second motor is automatical-
ly identified.
▪ Two motors can only be configures if the STM has been

planned accordingly (DUO).

▪ In case of RED doors 2 motors are compulsory.

Disabled

X One motor is connected.

Enabled

Two motors are connected.

Emergency operating BAT

This parameter determines the last action of the door controller
in battery operation. A second parameter

Power failure

(see

below) determines if this emergency operation should be exe-
cuted immediately after a power failure or only in case of low
battery capacity.
▪ At the end of the emergency operation (door open/closed)

the battery is completely disconnected, at the latest after

60 seconds. This state will only be exited upon return of
mains voltage.

▪ The last door movement happens at reduced speed. In

doing so, safety sensors are not taken into account, only

the collision identification is enabled.

▪ An emergency closing (NSK) or emergency opening (SÖK)

takes precedence over the configured emergency opera-
tion. Afterwards, the battery is also disconnected.

▪ If the battery capacity allows, the battery can be used for a

single door opening with the SSK.

▪ With RED doors only emergency operations in opening

direction are configurable.

Close, do not lock

Regardless of the operating mode the door is closed but not
locked.

Unlock and open

Regardless of the operating mode the door is completely
opened. If necessary, it is unlocked beforehand.

Close and lock

Regardless of the operating mode the door is closed and af-
terwards locked.

Open if not locked

X In the

Locked

operating mode the door remains locked or it is

locked after the next closing at the latest. In all the other oper-
ating modes the door is completely opened.

«
...
10
11
12
13
14
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 4

Бренд: Eastwood Страницы: 12

Бренд: quadient Страницы: 2

Air-Cooled Automatics ACAPTS-1.0

Бренд: Bernard Страницы: 4

Бренд: PROCRAFT Страницы: 25

UWI 230 TP AC/DC

Бренд: Unitor Страницы: 25

Бренд: Clarke Страницы: 16

Бренд: G-U Страницы: 20

Бренд: Westweld Страницы: 18

Multi-GMAW 200S

Бренд: MK Welding Страницы: 39

Бренд: Dormakaba Страницы: 10

3VL9800-3A 0 Series

Бренд: Siemens Страницы: 7

Бренд: Kompernass Страницы: 66

Бренд: Tucker Auto-Mation Страницы: 42

MULTIMIG 400puls

Бренд: Elektron Страницы: 20

Бренд: PRETUL Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды