Record system 20 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

30/ 56

→ Broken rubber cord

Monitoring of the rubber cord with door type CO48.
0V/open = rubber cord broken (switch open)
24V = rubber cord fine (switch closed)
▪ In case of torn cord, error 20 is displayed and the door

opens to the full opening width, provided that it is not
locked.

▪ Also, in case of torn cord, all operating modes including

Locked

, are still possible.

→ Opening dead man

Opening button for

Dead man

door type and other button-

operated doors.
0V/open = door stops
24V = door opens
▪ The door opens as long as the button is continuously

pressed. If another button is pressed at the same time, the

door stops.

→ Closing dead man

Closing button for

Dead man

door type and other button-

operated doors.
0V/open = door stops
24V = door opens
▪ The door closes as long as the button is continuously

pressed. If another button is pressed at the same time, the

door stops.

→ AKI button

(not with RED)

Opening to complete opening width with pulse signal (0V/open
-> 24V). The signal is intended for connecting a button on the
inner side of the door.
▪ An automatic door closes at the end of the hold-open time,

even if the button is maintained pressed.

▪ A locked door cannot be opened.

→ Interior button

(only AUX0_IN and
AUX1_IN with RED)

Moving to complete opening width with pulse signal (0V/open -
> 24V).
The signal is intended for connecting a button on the inner side
of the door.
▪ May only be used in an addition to a certified escape route

sensor. The button itself and the opening path over the
button are not monitored.

«
...
28
29
30
31
32
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 4

Бренд: Eastwood Страницы: 12

Welder / Generator GW4500

Бренд: Campbell Hausfeld Страницы: 20

Бренд: RTRMAX Страницы: 14

Taurus 401 Synergic S MM FKW

Бренд: EWM Страницы: 119

RIS 700PE EKO 3.0

Бренд: Salda Страницы: 36

Бренд: MAC TOOLS Страницы: 20

Бренд: Gude Страницы: 122

Бренд: Miller Страницы: 40

Бренд: Tecnosystemi Страницы: 16

Бренд: Miller Страницы: 32

Бренд: R-Tech Страницы: 17

Бренд: Dorma Страницы: 3

Бренд: Uni-Mig Страницы: 9

Бренд: Autoslide Страницы: 32

Бренд: Bartec Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды