Record system 20 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 57

background image

Parameter explanations V2.1_V2.6

2

IRA_B8_EN_2V2_REC_102-020401137

26/ 56

→ Locking type

Selection of the connected locking device. Due to the large
range of variants, the locking type cannot be identified auto-
matically.

→ Without

X No locking device is connected.

→ Motor-powered

VRR 20 (motor-powered, bi-stable)

→ Bi-stable

VRR 16 (magnetic, bi-stable)

→ MPV 20

Multipoint locking device for system 20 (motor-powered)

→ MPV 16

Multipoint locking device for system 16 (motor-powered)

→ Magnet

Magnet locking device (without VAK) unlocked without current
(mono-stable)

→ Fail secure

Mono-stable locking device, locked without current

→ Fail safe

Mono-stable locking device, unlocked without current
(France: sécurité positive)

→ Double

Control of the additional unit for 2 locking devices.
Is used with FBO and PST.

→ Start delay

0 Delay time until door opens after unlocking.

0 = no delay
40 = 8 seconds delay

→ Closed VRR error

In certain situations e.g. after a restart or a locking problem,
the control unit checks by means of a short opening movement
if the door is locked or not. This parameter allows configuring
the further behaviour in the case the door is not locked.

→ Disabled

X If the door is not locked, it stops when reaching a 10 cm open-

ing width and an error message is displayed.

→ Enabled

If the door is not locked, it closes again completely and an
error message is displayed.

→ Closing force

0 Briefly increases the closing force when locking and unlocking

in order to mechanically relieve the bolt.
0 = low closing pressure
40 = high closing pressure

«
...
24
25
26
27
28
...
»

Содержание system 20


























































Отзывы:

Нет отзывов

Похожие инструкции для system 20

Бренд: raumplus Страницы: 23

Бренд: CIGWELD Страницы: 116

RIS 400PE/PW EKO 3.0

Бренд: Salda Страницы: 68

Бренд: CAME Страницы: 40

Бренд: Xcel-Arc Страницы: 20

VIPER MULTI 135

Бренд: Unimig Страницы: 48

Бренд: CAME Страницы: 20

INVERTEC PC208 AUS

Бренд: Lincoln Electric Страницы: 14

Torchmate Flexcut 80

Бренд: Lincoln Electric Страницы: 2

Бренд: STAMOS Страницы: 7

STANDARDTIG-160

Бренд: Paton Страницы: 115

Бренд: Parweld Страницы: 17

Бренд: Würth Страницы: 40

Бренд: Woodhaven Страницы: 2

Бренд: Kedr Страницы: 26

Бренд: Boss Страницы: 31

Бренд: Chamberlain Страницы: 76

Бренд: ABH Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды