Record system 20 Скачать руководство пользователя страница 41

Страница: 41 / 57

Parameter explanations V2.1_V2.6

IRA_B8_EN_2V2_REC_102-020401137

41/ 56

→ Reduced OM

The relay is active as long as an operating mode with

reduced

opening width

is activated.

→ Power failure

The relay is active as long as there is no mains voltage and
the control unit is operated by battery.
▪ If

Parameter → Drive → Power failure

is configured for

Bat-

tery operation

, the relay remains active until the control unit

changes to sleep mode.

▪ If

Parameter → Drive → Power failure

is configured for

Emergency operation

, the relay only remains active during

the action configured with

Parameter → Emergency opera-

tion battery

. Afterwards the control unit change to sleep

mode and the relay is deactivated.

→ Locking error

The relay is active as long as a locking or unlocking error has
been detected.

→ Battery error

Relay active during a battery error.
▪ Depending on door type the battery might only be tested

once per hour.

Accordingly, it can last up to an hour until a battery defect

is displayed.

→ ELS error

Relay active during an ELS error.

→ Emergency stop/open

Relay active while connection

Emergency stop

Emergency

open

is cut.

→ AKI/AKA time

The relay is active while an AKI or AKA triggering signal re-
mains activated.
▪ The time until the output is activated can be adjusted with

Parameter → Miscellaneous → Alarm display → Time acti-

vation

→ SÖK/NSK

The relay is active while an SÖK or NSK signal is triggered.

→ CAN connection

The relay is active as long as there is a problem with the CAN
connection between STM and FEM1.

→ Error RED test

The relay is activated.

→ Maintenance is due

The relay is activated when 95% of the maintenance target
value is reached.

→ Maintenance time ex-

ceeded

The relay is activated when 105% of the maintenance target
value is reached.

→ Redundancy test

The relay is activated while a redundancy test is being carried
out.

Содержание system 20


























































Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды

Record system 20, Перевод оригинального руководства

Результаты поиска

Содержание system 20

Отзывы:

Похожие инструкции для system 20

Бренды по названию

Популярные бренды