Rational Combi Master, Руководство по обучению

Страница: 197 / 200

197
SCC
Edition 10-2008a
Service error code: Service 10
SC-Pump without Function
Service 1
1
level electrode (Osmosis water) or check valve above steam generator for leakage
Service 12
CDS sensor no output signal
Service 13
change level electrode
Service 14
Level electrode (Osmosis water)
Service 16
since 01-07-09,
ash new software version
rst
Service 17
external EEPROM faulty
Service 20
thermocouple B1 faulty
Service 21
micro switch clima control faulty
Service 22 Service 23
SSR steam short circuit
Service 24
SSR hot air short circuit
Service 25
CleanJet water circulation faulty - water doesn‘t hit fan wheel - check pump, foreign bodies in water pipe, racks / trolley must be inside cabinet
Service 26
drain valve closed
Service 27
drain valve doesn‘t close, CleanJet without function
Service 28
B5 in steam generator above 180°C (356°F), de-scale steam generator
Service 29
pcb temperature too high (above 85°C / 185°F); change air
lter
Service 30
humidity control faulty
Service 31.X
core probe faulty
Service 32.X
ignition box faulty
, change ignition box
0-top; 1-bottom; 2-both
Service 33.X
4x Reset without function, change ignition box; 1-top; 2-bottom
Service 34.X
BUS signal error 1-I/O pcb, 2-motor bottom; 4-motor top; 8-ignition box top; 16-ignition box bottom
Service error code: Service 40
Cleanjet not possible, Care pump faulty
Service 41
CDS does not send any pulses; solenoid valve
Y3 defective or moistening valve
blocked;
Service 42
CDS does not send any pulses; Solenoid Y4 Care defective or hose to care contai- ner blocked up or kinked;
Service 43
CDS sensor sends always pulses; Soleno- id
Y1,
Y3 or
Y4 is passing water
Service 44
Steam heating or SSR faulty
Service 100
Main contactor - pcb on of
f switch
Service 1
10
SC pump faulty or level electrode calci
es
Service 120
Care Pump M12 or level electrode defec- tive
Gas-settings - values Dyn. pressure LPG
27-57 mbar; 2,7-5,7 kPa
Dyn. pressure natural gas
18-25 mbar; 1,8-2,5 kPa
CO2 max LPG (G30) 3BP
10,4% +/- 0,2% for type 61-202
CO2 max LPG (G31) 3P
1
1,1% +/- 0,2% for type 61-202
CO2 max natural gas H (G20)
9,4% +/- 0,2% for type 61-201 9,5% +/- 0,2% for type 202
CO2 max natural gas L (G25)
9,3% +/- 0,2% for type 61-201 9,4% +/- 0,2% for type 202
Calibration SCC
Calibration at the customers site must be done under the following conditions: Changing of: 1
Pressure sensor P1,
2
B4 humidity sensor
,
3 fan
motor
,
4 pcb, 5 external
EEPROM,
6
detaching of the fan wheel,
7
replacing the air baf
e or divider plate between the 2 fan
motors of a
oor
model,
8
installation of the appliance above 1000m (3000ft) above
sea
level or below sea level (dead sea),
installing with Ultravent of venting extension or as a Combi Duo 9
Usage of a dif
ferent standard rack
10
Customer complaint for uneven cooking results
Basic condition T
emperatures:
Cabinet sensor Quench. sensor Humidity sensor
B1 <40°C
B2 <45°C
B4 < 40°C
Basic condition Hardware: Heating: OFF Fan motor: OFF Humidity
ap:
Closed
Side panel must be
tted; Unit must be clean, but may be wet
In order to achieve the best possible calibration values, insert 2 GN-container 20 or 40 mm deep with the opening facing downwards in 61 and 62 units into rail 2 and 5 in 101 and 102 units into rail 3 and 7 in 201 and 202 units 3 GN container into rail 3, 10 and 17 T
o start calibration: Set DIP
switch 1 in on pcb, Select:
Basic Settings, Pkt. 1.1: ST
ART