SECTION 19: T
ROUBLESHOOTING
137 of 143
Burner Control Module (continued)
BLINK CODE
SYSTEM FAILURE
RECOMMENDED TROUBLESHOOTING
Code 4-3*Flame Amplifier
Pro
b
lem*
Flame not sensed, or sensed
w
hen it sho
u
ld
b
e on or off.
1. Check
w
iring; correct any errors.
2. Make s
u
re the flame amplifier and flame detector are
compati
b
le.
3. Remo
v
e the flame amplifier and inspect the connections.
Reseat the amplifier.
4. Reset and seq
u
ence the relay mod
u
le.
5. If the code reappears, replace the flame amplifier and/or
the flame detector.
6. If the fa
u
lt persists, replace the relay mod
u
le.
Code 4-4*Config
u
ration
J
u
mper Pro
b
lem*
The config
u
ration j
u
mpers dif-
fer from the sample taken at
start
u
p.
1. Inspect the j
u
mper connections. Make s
u
re the clipped
j
u
mpers
w
ere completely remo
v
ed.
2. Reset and seq
u
ence the relay mod
u
le.
3. If the fa
u
lt persists, replace the relay mod
u
le.
Code 5-1*Pre-Ignition
Interlock*
Pre-Ignition Interlock fa
u
lt.
1. Check
w
iring and correct any errors.
2. Check pre-ignition interlock s
w
itches to ass
u
re proper
f
u
nctioning.
3. Check f
u
el
v
al
v
e operation.
4. Reset and seq
u
ence the relay mod
u
le; monitor the
Pre-Ignition Interlock stat
u
s.
5. If the fa
u
lt persists, replace the relay mod
u
le.
Code 5-2*High Fire S
w
. or
Lo
w
Fire S
w
.*
Either High Fire S
w
itch or
Lo
w
Fire S
w
itch fail
u
re.
1. Check
w
iring and correct any errors.
2. Reset and seq
u
ence the relay mod
u
le.
3. Use man
u
al motor potentiometer to dri
v
e the motor open
and closed. Verify at motor s
w
itch that the end s
w
itches
are operating properly. Use RUN/TEST s
w
itch if man
u
al
potentiometer is not a
v
aila
b
le.
4. Reset and seq
u
ence the relay mod
u
le.
5. If the fa
u
lt persists, replace the relay mod
u
le.
Code 5-3*Man-Open S
w
.;
Start S
w
. or Control On*
Man-Open S
w
itch, Start
S
w
itch or Control On in the
w
rong operational state.
1. Check
w
iring and correct any errors.
2. Make s
u
re that the man
u
al open
v
al
v
e s
w
itch, start
s
w
itch and control are operating properly.
3. Stat S
w
itch held “On” too long.
4. Reset and seq
u
ence the relay mod
u
le.
5. Reset and seq
u
ence the relay mod
u
le. If the fa
u
lt
persists, replace the relay mod
u
le (RM7838A1014;
RM7838B1013 or RM7838C1004 only).
Code 6-1*Internal Fa
u
lts* Relay Mod
u
le self-test fail
u
re. 1. Reset and seq
u
ence the relay mod
u
le.
2. If fa
u
lt reappears, remo
v
e po
w
er from the de
v
ice, reapply
po
w
er, then reset and seq
u
ence the relay mod
u
le.
3. If the fa
u
lt persists, replace the relay mod
u
le.
Code 6-2*Internal Fa
u
lts* Relay Mod
u
le Self-Test
fail
u
re.
1. Reset and seq
u
ence the relay mod
u
le.
2. If fa
u
lt reappears, remo
v
e po
w
er from the de
v
ice, reapply
po
w
er, then reset and seq
u
ence the relay mod
u
le.
3. If fa
u
lt does not repeat on the next cycle, check for
electrical noise
b
eing copied into the relay mod
u
le
thro
u
gh the external loads or possi
b
ly an electrical
gro
u
nding iss
u
e.
4. If the fa
u
lt persists, replace the relay mod
u
le.
Содержание 7500 136
