![background image](http://html1.mh-extra.com/html/ransburg/19372/19372_service-manual_3683758026.webp)
AH-95-02.4
2 2
2 2
2 2
2 2
2 2
SCHEDULES
SCHEDULES
SCHEDULES
SCHEDULES
SCHEDULES
Periodic
Periodic
Periodic
Periodic
Periodic
To assure continuous, efficient, troublefree
operation of the No. 2 handgun, periodic inspec-
tion of the components is required. Clean,
repair and/or replace any defective components
as required.
Daily
Daily
Daily
Daily
Daily
1.
Prior to start-up, inspect all components
of the system for defective or broken
parts and repair or replace.
2.
Inspect the bell for chips or cracks and
replace as needed.
3.
Ensure the equipment is installed prop-
erly. See the "Installation" section.
4.
Clean the fluid line filter (item 80). See
"Filter Cleaning or Replacement" in the
"Maintenance" section of this manual.
Prior to gun disassembly, flush line and
gun with a suitable solvent. Loosen the set
screw on the bell hub, remove, and clean
the bell with a soft brush (nonmetallic) or
cloth and a suitable solvent. The bell
MUST
MUST
MUST
MUST
MUST be cleaned if spraying is to be in-
terrupted for more than a few minutes.
N O T E
N O T E
N O T E
N O T E
N O T E
NEVER
NEVER
NEVER
NEVER
NEVER wrap the applicator, associated
valves and tubing, and supporting hardware
in plastic to keep it clean. A surface charge
may build up on the plastic surface and
discharge to the nearest grounded object.
Efficiency of the applicator will also be
reduced and damage or failure of the
applicator's components may occur.
WRAPPING THESE COMPONENTS
WRAPPING THESE COMPONENTS
WRAPPING THESE COMPONENTS
WRAPPING THESE COMPONENTS
WRAPPING THESE COMPONENTS
IN PLASTIC WILL VOID WARRANTY.
IN PLASTIC WILL VOID WARRANTY.
IN PLASTIC WILL VOID WARRANTY.
IN PLASTIC WILL VOID WARRANTY.
IN PLASTIC WILL VOID WARRANTY.
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
!!!!!
Weekly
Weekly
Weekly
Weekly
Weekly
1.
Inspect all equipment for damage, leaks,
or paint buildup.
2.
Measure the electrical output of the gun.
The short circuit current should be 80 to
100 microamperes (.08 to .10 milliam-
peres on some meter scales). Refer to
the "Gun Output Test (SCI)" in the
"Maintenance" section for procedure.
3.
Check ALL o-rings for fit and deteriora-
tion.
Primary fluid control is through the
paint pot regulator.
N O T E
N O T E
N O T E
N O T E
N O T E
TEST PROCEDURES
TEST PROCEDURES
TEST PROCEDURES
TEST PROCEDURES
TEST PROCEDURES
Fluid T
Fluid T
Fluid T
Fluid T
Fluid Testing
esting
esting
esting
esting
When the paint does not shut-off after the trigger
has been released, adjust the knurled nuts (in
front of trigger). If this does not correct the
problem, refer to the "Troubleshooting Guide"
(Figure 11).
1.
Turn the outer locknut a few times coun-
terclockwise. DO NOT
DO NOT
DO NOT
DO NOT
DO NOT thread it off the
needle.
2.
Adjust the inner locknut counterclock-
wise, to allow the needle to completely
seat, and hold the trigger firmly.
3.
Make further adjustments of the outer
and inner locknuts as needed for fine ad-
justment of fluid delivery with thin vis-
cosity paints.
Содержание 19372
Страница 4: ...AH 95 02 4...
Страница 61: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...
Страница 62: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...