![background image](http://html1.mh-extra.com/html/ransburg/19372/19372_service-manual_3683758028.webp)
AH-95-02.4
2 4
2 4
2 4
2 4
2 4
REP
REP
REP
REP
REPAIR PROCEDURES
AIR PROCEDURES
AIR PROCEDURES
AIR PROCEDURES
AIR PROCEDURES
Read each procedure entirely before beginning.
High voltage components, such as
cable and high voltage resistor, are not
field serviceable. For repair or replace-
ment of such items, call your Ransburg
distributor.
N O T E
N O T E
N O T E
N O T E
N O T E
BEFORE
BEFORE
BEFORE
BEFORE
BEFORE attempting any cleaning or
color change procedures the high voltage
and the AC power to the power supply
MUST
MUST
MUST
MUST
MUST be turned OFF!
OFF!
OFF!
OFF!
OFF!
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
!!!!!
This method uses the microampmeter located
on the power supply.
1.
Remove the bell from the gun. Rotate
the contact brush outwards and touch
the contact brush to ground.
2.
Turn the power supply ON.
ON.
ON.
ON.
ON.
3.
Activate the motor circuit at the gun.
The meter of the power supply should
read approximately 80 to 100 microam-
peres.
T
T
T
T
Tools Required
ools Required
ools Required
ools Required
ools Required
9/16-inch Open End Wrench
5/8-inch Open End Wrench
3/4-inch Open End Wrench
9/64-inch Hex Wrench
6 inch Adjustable Wrench
1/4-inch Open End Wrench (Ignition Type)
Bench Vise, Flat Jawed
Spare Parts Kit (9096-00)
Pliers
Screwdriver
1/8-inch Straight Punch
5/16-inch Drill Bit
Preliminary Disassembly
Preliminary Disassembly
Preliminary Disassembly
Preliminary Disassembly
Preliminary Disassembly
Prior to performing any service on the gun the
following procedures should be followed:
1.
Turn the high voltage OFF and discon-
nect the AC power to the power supply.
2.
Flush the fluid line and gun with a suit-
able solvent.
3.
Loosen the set screw on the bell hub,
remove and clean the bell. Refer to "Ef-
fects of Solvents" in the "Maintenance"
section for a list of cleaning solvents.
4.
Turn fluid pressure OFF
OFF
OFF
OFF
OFF. Bleed all pres-
sure from the line.
5.
Disconnect the fluid at the rear of the
gun.
6.
Disconnect the high voltage cable from
the power supply.
Filter Cleaning or Replacement
Filter Cleaning or Replacement
Filter Cleaning or Replacement
Filter Cleaning or Replacement
Filter Cleaning or Replacement
-REFER TO FIGURE 7 & 14d
-REFER TO FIGURE 7 & 14d
-REFER TO FIGURE 7 & 14d
-REFER TO FIGURE 7 & 14d
-REFER TO FIGURE 7 & 14d
1.
Disconnect the fluid hose assembly
(item 71) from the filter assembly (item
80). Hold the filter assembly rear hous-
ing with a 3/4-inch open end wrench and
with a 5/8-inch open end wrench turn the
fluid hose nut (item 71B) in a clockwise
direction (left hand threads) to remove
the fluid hose.
2.
Disconnect the filter assembly (item 80)
from the gun assembly. Secure the
hose connector assembly (item 65) with
a 5/8-inch open end wrench and with a
3/4-inch open end wrench connected to
the filter assembly nut (item 80F), turn
the nut clockwise and remove the filter
assembly.
Содержание 19372
Страница 4: ...AH 95 02 4...
Страница 61: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...
Страница 62: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...