![background image](http://html1.mh-extra.com/html/ransburg/19372/19372_service-manual_3683758021.webp)
AH-95-02.4
1 7
1 7
1 7
1 7
1 7
6.
Wipe the gun, cable, and the hose with a
rag and suitable mild solvent for the
coating being sprayed.
NEVER
NEVER
NEVER
NEVER
NEVER soak or submerge the
assembled gun!
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
!!!!!
Color Change
Color Change
Color Change
Color Change
Color Change
If the gun is to be flushed with solvent between
colors (as when switching between two incom-
patible colors or paints), turn ALL
ALL
ALL
ALL
ALL electrical
power OFF
OFF
OFF
OFF
OFF and carefully follow the gun clean-
ing and color change procedures as outlined in
the following steps.
1.
Turn the gun motor OFF.
OFF.
OFF.
OFF.
OFF. Release the
paint pressure at the pressure regulator
and mount the gun on its stand.
BEFORE
BEFORE
BEFORE
BEFORE
BEFORE attempting any cleaning or
color change procedures, the high voltage
and the AC power to the power supply
MUST
MUST
MUST
MUST
MUST be turned OFF!
OFF!
OFF!
OFF!
OFF!
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
!!!!!
2.
Regulate the pressure to normal operat-
ing setting (or high for faster cleaning)
and use one or two quarts of any suit-
able cleaning solvent that is compatible
with the paint being used.
If your equipment has an individual
pressurized container and hose for each
paint and solvent, or individual hoses for
use with a pump, disconnect the gun.
When one pressure pot and a single
hose is used, replace the paint container
with a solvent container.
If the hose is used with a pump, remove
the pump pick-up tube from the paint and
place it in a solvent-filled container.
N O T E
N O T E
N O T E
N O T E
N O T E
3.
Remove the gun from its stand and be
sure that the electric power is turned
OFF
OFF
OFF
OFF
OFF. Position the feed tube and the
contact brush upward and remove the
bell from the gun by following the steps
outlined under "Shutdown" in the "Opera-
tion" section.
4.
Reposition the feed tube to the five
oclock position and trigger the gun into a
grounded container until there is no evi-
dence of paint in the stream.
5.
Release the trigger and remove the feed
tube (item 12). Wipe the feed tube thor-
oughly. Pull trigger to flush material
trapped by feed tube o-ring.
6.
Release the trigger, replace the gun on
the stand, and release the fluid pressure.
Reinstall the feed tube (item 12). Feed
tube o-ring may swell from solvent and
need regular replacement.
7.
Connect the gun to the new paint supply,
set for normal operation, and apply pres-
sure.
8.
Trigger the gun for a few seconds to re-
move all of the solvent from it and the
hose (until paint flows from feed tube).
Replace the bell and reposition the feed
tube (item 12) and the contact brush
(item 41).
9.
Turn the gun motor and high voltage
switch ON
ON
ON
ON
ON and resume normal opera-
tion.
Paints and solvents SHOULD ONLY
SHOULD ONLY
SHOULD ONLY
SHOULD ONLY
SHOULD ONLY
be flushed into grounded metal safety
containers.
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
!!!!!
Keep the barrel of the gun angled down
until the solvent is completely out of it.
N O T E
N O T E
N O T E
N O T E
N O T E
Содержание 19372
Страница 4: ...AH 95 02 4...
Страница 61: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...
Страница 62: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...