AH-95-02.4
3 7
3 7
3 7
3 7
3 7
9.
Install o-ring (item 4) on ceramic seal
(item 5) and slide the ceramic seal onto
drive shaft (item 9) until it contacts
Teflon seal (item 6).
10.
Place the nut (item 3) onto drive shaft
(item 9) side with threads toward ce-
ramic seal (item 5). Slide it back on
drive shaft as far as it will go.
11.
Slip the collar (item 2) onto the drive
shaft (item 9), centering it over the
groove (old style drive shaft) or align the
two set screws with the two flats in drive
shaft (new style drive shaft). Secure the
collar to the drive shaft by tightening the
two set screws (item 1).
Lightly lubricate the o-rings only with
petroleum jelly. DO NOT USE SILI-
DO NOT USE SILI-
DO NOT USE SILI-
DO NOT USE SILI-
DO NOT USE SILI-
CONE LUBRICANTS!
CONE LUBRICANTS!
CONE LUBRICANTS!
CONE LUBRICANTS!
CONE LUBRICANTS!
N O T E
N O T E
N O T E
N O T E
N O T E
Clean the inner and outer faces of the
new seals and the front portion of the shaft
carefully with solvent before replacing
them. Oil or dirt deposit from the hands
could cause an improper contact of seal
faces. This is a DRY
DRY
DRY
DRY
DRY seal and DOES
DOES
DOES
DOES
DOES
NOT
NOT
NOT
NOT
NOT require grease or oil.
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
!!!!!
2.
Remove the o-ring (item 8) from the
drive shaft (item 9), taking care not to
damage the drive shaft.
3.
Using a screwdriver, loosen the two set
screws (item 1) (about two turns coun-
terclockwise) of the collar (item 2) and
remove the collar and nut (item 3) from
the drive shaft (item 9).
4.
Slide outer ceramic seal (item 5) and in-
ner Teflon seal (item 6) off the drive
shaft (item 9).
5.
Remove the remaining two o-rings
(items 7 and 8) from the drive shaft (item
9).
6.
Discard the ceramic seal (item 5), Teflon
seal (item 6), o-rings (items 4, 7, and 8).
Examine the drive shaft (item 9) and re-
place if damaged.
7.
Slide o-ring (item 7) over drive shaft
(item 9) until it bottoms on shoulder. In-
stall o-ring (item 8) into second o-ring
groove of drive shaft.
8.
Place Teflon seal (item 6), with shoulder
facing toward front end of drive shaft,
onto the drive shaft (item 9) and slide it
back until it contacts o-ring (item 7).
DO NOT Apply Dielectric Grease
DO NOT Apply Dielectric Grease
DO NOT Apply Dielectric Grease
DO NOT Apply Dielectric Grease
DO NOT Apply Dielectric Grease
or Any Other Lubricant to the Teflon
or Any Other Lubricant to the Teflon
or Any Other Lubricant to the Teflon
or Any Other Lubricant to the Teflon
or Any Other Lubricant to the Teflon
Seal (Item 6), Ceramic Seal (Item 5),
Seal (Item 6), Ceramic Seal (Item 5),
Seal (Item 6), Ceramic Seal (Item 5),
Seal (Item 6), Ceramic Seal (Item 5),
Seal (Item 6), Ceramic Seal (Item 5),
Drive Shaft (Item 9), or Collar (Item
Drive Shaft (Item 9), or Collar (Item
Drive Shaft (Item 9), or Collar (Item
Drive Shaft (Item 9), or Collar (Item
Drive Shaft (Item 9), or Collar (Item
1).
1).
1).
1).
1). The application of dielectric grease or
any other lubricant to these components
can cause premature failure of the motor.
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
C A U T I O N
!!!!!
Figure 12: Ceramic Bearing Assembly
Figure 12: Ceramic Bearing Assembly
Figure 12: Ceramic Bearing Assembly
Figure 12: Ceramic Bearing Assembly
Figure 12: Ceramic Bearing Assembly
Содержание 19372
Страница 4: ...AH 95 02 4...
Страница 61: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...
Страница 62: ...AH 95 02 4 NOTES NOTES NOTES NOTES NOTES...