Rane HAL1 Скачать руководство пользователя страница 56

Страница: 56 / 68

RAD Status Indicators

Possible Causes

Suggested Action

GREEN

RED

GREEN

RED

The twisted pair in
the CAT 5 cable
that carries com-
munications data is
miswired or broken.

Use a cable tester to
verify the wiring of the
CAT 5 cable.

If using a punch block,
verify that the orange
pair is properly
punched (assuming
T568B termination).

GREEN

RED

The RAD is not
receiving an audio
stream from the
HAL.

Use a cable tester to
verify CAT 5 ter-
mination.

If using a punch block,
verify that the green
pair is properly
punched (assuming
T568B termination).

GREEN

RED

GREEN

The HAL is not
receiving an audio
stream from the
RAD.

Use a cable tester to
verify CAT 5 ter-
mination.

If using a punch block,
verify that the blue
pair is properly
punched (assuming
T568B termination).

FLASHING

GREEN

FLASHING

GREEN

FLASHING

GREEN

FLASHING

GREEN

The RAD is in
Locate mode.

End Locate mode for
that RAD from within
Halogen.

FLASHING

RED

FLASHING

RED

FLASHING

RED

FLASHING

RED

The connected RAD
does not match the
configured RAD
model.

Adjust the con-
figuration or connect
the correct RAD model
to the port. The sim-
plest solution is often
to swap RADs in the
Halogen software. See
Swapping Devices in
the Halogen Help Sys-
tem.

HAL SYSTEM INSTALLATION GUIDE

Содержание HAL1





































































Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды

Rane HAL1, Руководство по установке системы

Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды