Rane HAL1 Скачать руководство пользователя страница 67

Страница: 67 / 68

HAL

System Installation Guide

(Signature)

October 5, 2011

(Date)

Mukilteo WA USA

(Place)

Compliance Engineer

(Position)

Greg Frederick

(Full Name)

Declaration of Conformity

Application of Council directive(s):

2006/95/EC

2004/108/EC

2002/96/EC

2002/95/EC

Manufacturer:

Rane Corporation

10802 47th Avenue West

Mukilteo WA 98275-5098 USA

This equipment has been tested and found to be in compliance with all applicable standards and regulations applying to the EU’s Low

Voltage (LV) directive 2006/95/EC, and Electromagnetic Compatibility (EMC) directive 2004/108/EC. In order for the customer to

maintain compliance with this regulation, high quality shielded cable must be used for interconnection to other equipment. Modification

of the equipment, other than that expressly outlined by the manufacturer, is not allowed under this directive. The user of this equipment

shall accept full responsibility for compliance with the LV directive and EMC directive in the event that the equipment is modified with-

out written consent of the manufacturer.

Type of Equipment:

Professional Audio Signal Processing

Model:

HAL1

Immunity Results:

THD+N: 4 dBu, 400 Hz, BW = 20 Hz - 20 kHz

Test Description

Measurement

Conditions

RF Electromagnetic Fields Immunity

80 MHz -2700 MHz

< -83 dB

1 kHz AM, 80% depth, 3 V/m

Conducted RF Disturbances Immunity

150 kHz - 80 MHz

< -69 dB

1 kHz AM, 80% depth, 3 Vrms

Magnetic Fields Immunity

50Hz - 10kHz

< -82 dB

3.0 - 0.3 A/m

Common Mode Immunity (Signal Ports):

Bandpass re: 4 dBu, 1/3-octave

50Hz - 10kHz, -20dBu

< -60 dB

Common Mode Immunity (Data Ports):

Bandpass re: 4 dBu, 1/3-octave

50Hz - 10kHz, -20dBu

< -70 dB

I, the undersigned, hereby declare that the equipment specified above conforms

to the Directive(s) and Standard(s) shown above.

Standard(s) to which

conformity is declared:

EN60065: Ed. 7.1 (2005)

EN55103-1:1996

EN55103-2:1996

ENVIRONMENT E2

Serial Numbers 600000-700000

Содержание HAL1





































































Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды

Rane HAL1, Руководство по установке системы

Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды