Rane HAL1 Скачать руководство пользователя

Страница: 1 / 68

HAL

System Installation Guide

Halogen Software Version 1.0.0

17945

+ –

REMOTE AUDIO DEVICES & DR

DIGITAL REMOTES

EXPANSION BUS

ETHERNET

REMOTE AUDIO DEVICES

DIGITAL REMOTES

3 2 1

LINK

LAN

LINK

LOCATE

FAULT

POWER

COMM

POWER

COMM

POWER

AUDIO TX

AUDIO RX

MIC / LINE INPUTS

LINE OUTPUTS

RELAY OUT

LOGIC IN

C NC NO C NC NO

G 4 3 2 1 G

SHIELDED CAT5e OR BETTER

24 VDC @ 100 mA

24 VDC @ 50 mA

ACN 001 345 482

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

MADE IN U.S.A.

RANE CORP.

HAL1

100-240 V

50/60 Hz 55 WATTS

CLASS 2 WIRING

LOCATE

POWER

ACN 001 345 482

CLASS 2 WIRING

MADE IN U.S.A.

RANE CORP.

EXP1

100-240 V

50/60 Hz 30 WATTS

REMOTE AUDIO DEVICES & DR

REMOTE AUDIO DEVICES

8 7 6 5 4 3 2 1

COMM

POWER

AUDIO TX

AUDIO RX

EXPANSION BUS

LINK

SHIELDED CAT 5e OR BETTER

24 VDC @ 100 mA

This device complies with

Part 15 of the FCC Rules.

Operation is subject to the

following two conditions:

(1) this device may not

cause harmful interference,

and (2) this device must

accept any interference

received, including

interference that may cause

undesired operation.

PUSH • SELECT

SCROLL

DR3

MICROPHONE

LINE OUTPUT

SIG / OL

AUDIO RX

AUDIO TX

SIG / OL

POWER

COMM

SIG / OL

RAD12

LINE INPUT

MICROPHONE

SIG / OL

AUDIO RX

AUDIO TX

RAD2

SIG / OL

POWER

COMM

MICROPHONE

LINE INPUT

POWER

COMM

SIG / OL

AUDIO RX

AUDIO TX

RAD7

LINE OUTPUT

MICROPHONE

SIG / OL

AUDIO RX

AUDIO TX

SIG / OL

POWER

COMM

RAD8

PUSH • SELECT

DR1

PUSH • SELECT

DR1

PUSH • SELECT

DR1

MICROPHONE

SIG / OL

AUDIO RX

AUDIO TX

RAD1

SIG / OL

POWER

COMM

LINE INPUT

MICROPHONE

SIG / OL

AUDIO RX

AUDIO TX

RAD2

SIG / OL

POWER

COMM

PUSH • SELECT

SCROLL

DR2

LINE OUTPUT

SIG / OL

POWER

COMM

AUDIO RX

AUDIO TX

RAD4

Содержание HAL1





































































Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды

Rane HAL1, Руководство по установке системы

Результаты поиска

Содержание HAL1

Отзывы:

Похожие инструкции для HAL1

Бренды по названию

Популярные бренды