Radian RM-111 Скачать руководство пользователя страница 71

Страница: 71 / 97

RM-111 Operations Manual

Form: Enter the meter form.

KH - Enter the DUT Kh value.

PriKh – Enter the primary reference standard(s) Kh value.

Test by* – Select either Revs or Energy.

#Standards – Enter the number of reference standards that will be used. For this application, enter
three.

Mode – If more than one reference standard is used, the user must choose between single-phase or
polyphase modes of operation. For this application, enter polyphase.

Ref Type – This defi nes the reference standard output pull-up value. Select Radian (150 ohm).
Other is 1000 ohm.

#Inputs – Enter the number of current inputs used for the reference standard(s).

SER#1 – Enter a serial number for standard 1, if applicable.

SER#2 – Enter a serial number for standard 2, if applicable.

SER#3 – Enter a serial number for standard 3, if applicable.

Element – Enter the number of meter elements.

FL Revs – Enter the desired number of revolutions for the full load test (FL).

PF Revs – Enter the desired number of revolutions for the power factor test (PF).

LL Revs – Enter the desired number of revolutions for the light load test (LL).

FL WAVG – Enter the desired weight of the measured FL value in the weighted average
calculation.

PF WAVG – Enter the desired weight of the measured PF value in the weighted average
calculation.

LL WAVG – Enter the desired weight of the measured LL value in the weighted average
calculation.

Application 9

Содержание RM-111


































































































Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды

Radian RM-111, Руководство по эксплуатации

Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды