Radian RM-111 Скачать руководство пользователя страница 21

Страница: 21 / 97

RM-111 Operations Manual

Main Menu

Create

– Allows user to create a new meter test setup.

Delete

– Allows user to delete a meter test setup.

Preferences

RM-111 Link Mode

– Puts the RM-111 in a communication mode, allowing Radian data

collection and confi guration software applications to completely take control of the RM-111. The
RM-111 must be in this mode to either upload or download test information and results.

Results Display

– Selects either percent registration or percent error.

Result Digits

– Selects results resolution-either one, two, or three places to the right of the

decimal point.

Kh Format

– Allows the user to select the Kh format in the test setups screen – Pulses/Wh or

Wh/pulse.

User Prompts

– Specifi c meter and tester information is entered to enhance the test results. These

entries will also be stored with the results. All user prompts can be enabled or disabled directly
from the RM-111 YES/NO keys.

Enter Test Voltage

– The service voltage of the meter under test.

Enter Test Amps

– The test amps of the meter under test.

Enter Meter Form

– The form number of the meter under test.

Enter Tester ID#

- The tester’s identifi cation number, if applicable.

Enter Manufacturer ID#

- The manufacturer’s identifi cation number, if applicable.

Enter Beep

– Enables or disables the RM-111’s audible response.

Содержание RM-111


































































































Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды

Radian RM-111, Руководство по эксплуатации

Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды