Radian RM-111 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 97

background image

RM-111 Operations Manual

LL WAVG – Enter the desired weight of the measured LL value in the weighted average
calculation.

Demand – Enter the desired number of minutes for the demand test. To omit the demand test,
enter zero.

Pulses/Rev – Enter the number of pulses (or equivalent pulses) per revolution of the meter under
test. Use the calculations above and enter one pulse per Ke value.

Creep Mins – Enter the desired number of minutes to be used for the Creep test.

* The “

Test By:

” parameter input allows the user to select the type of tests –

Revs

or

Energy

.

if

Energy

is selected, the “

FL Revs:

”,”

PF Revs:

”, and “

LL Revs:

” parameter inputs dynamically

change to “

FL Wh:

”, “

PF Wh:

”, and “

LL Wh:

”.This allows a test to be stopped after a pre-set

amount of energy has been accumulated by the DUT.

4. Press ENTER to exit the Test Setup screen.

5. From the Main Menu select RUN TESTS.

6. Select Test Meter.

7. Select the previously confi gured test setup.

8. The RM-111 will prompt the user to select either a Manual (RM-1S or RR-1S) test or a Pulse
Sensor (RM-DS, RR-DS, RM-1H, or RR-1H) test. Select Pulse Sensor. Select BNC if using an
RM-1H or RM-DS, or select Lemo if using an RR-1H or RR-DS.

9. If not already completed, follow the prompts on the RM-111 to make the appropriate
connections. If using an RM-1H or RR-1H, see Figure 12.0 “Testing a Solid State Meter Using
Calibration LED Output.” If using an RM-DS or RR-DS, see Figure 13.0 “Testing an Induction
Meter Using an Edge Test.” The number of reference standards defi ned in the test setup determine
how the ports are confi gured. If using the RM-1H or RM-DS, connect it to port A. If using the
RR-1H or RR-DS, connect it to the PICKUP input. Connect the standards to ports B, C, and D.

10. Once connections are complete, press ENTER to start the test.

11. The RM-111 starts the ALIGN PULSE SENSOR TEST to allow for the pulse sensor to be
checked. During this time, the disk rotates at full load current. When the 1H or DS sensor is

Application 8

Application 8

65

«
...
64
65
66
67
68
...
»

Содержание RM-111


































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-111

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: Oakton Страницы: 16

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: Parkside Страницы: 114

Бренд: Vaisala Страницы: 2

Бренд: OBD Страницы: 5

Бренд: AR Страницы: 8

Бренд: janitza Страницы: 128

Бренд: Autometers Systems Страницы: 16

Бренд: Aethra Страницы: 2

Бренд: Flymaster Страницы: 7

Бренд: ADDAC System Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды