background image

RM-111 Operations Manual

14. To re-run the test select Re-Run Test. The pulses will be counted again and the new count will 
be displayed on the RM-111. Press ENTER to continue.

15. To display the calculated results select Show Results. The end count is displayed along with 
a down arrow icon in the lower right corner. This icon references the DOWN ARROW key on 
the RM-111 hand controller. By pressing the DOWN ARROW key the RM-111 displays the 
calculated results. Using the UP/DOWN ARROW keys the user can move between the watthour 
count and the calculated results.

16. To print the results connect the RM-RPP Remote Portable Printer to the SERIAL PORT on the 
RM-111. Turn the RM-RPP to the ON 1 position. Select Print Results. This will start the printing 
process. The printout is time/date stamped and includes both the watthour count and the calculated 
% Registration or % Error.

17. To save the results select Save Results. The RM-111 will prompt the user for the enabled 
parameters in the User Prompts menu and save the test results.

Application 7

Application 7

60

Содержание RM-111


































































































Отзывы: