Radian RM-111 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 97

Radian RM-111 Скачать руководство пользователя страница 90

RM-111 Operations Manual

Test Accessories

Test Accessories

22.0 Test Accessories

The

RM-1S Remote Reset Switch

is a normally closed push button switch. The RM-1S connects

directly to port A of the RM-111 Automated Comparator. The switch of the RM-1S is hermetically
sealed to provide increased reliability during fi eld use. The push-button has tactile feel to provide
instantaneous feedback of switch actuation.

The

RM-1H Infrared Optical Pickup

is used to sense the infrared pulses from the calibration LED

of solid state meters. The pulses from the RM-1H are fed into the input of the RM-111 into port A.
When the RM-1H is used with the RM-111 Automated Comparator the testing of solid state meters
is done automatically. The wide angular displacement of this sensor allows for fast, non-critical
alignment. Also, automatic gain control circuitry of the RM-1H assures operation in all ambient
sunlight conditions. The RM-1H/v is also available for those solid state meters that have a visible
calibration LED.

89

«
...
88
89
90
91
92
...
»

Содержание RM-111


































































































Отзывы:

Нет отзывов