Radian RM-111 Скачать руководство пользователя страница 32

Страница: 32 / 97

RM-111 Operations Manual

Name - Enter a test setup name on the fi rst line by typing over the current text (16 characters
maximum).

PriKh – Enter the primary reference standard(s) Kh value.

Kh – Enter the D.U.T. Kh value.

#Pulse – Enter the number of pulses for the reference standard(s) to output before stopping the
test.

Time* – not applicable for this test

Test by* – Select PULSE

Type – Select Cnt Pulse for the gating method

#Standards – Enter the number of reference standards that will be used. For this application enter
three.

Mode – If more than one reference standard is used, the user must choose between single-phase or
polyphase modes of operation. For this application select polyphase.

Ref Type – This defi nes the reference standard output pull-up value. Select Radian (150 ohm).
Other is 1000 ohm.

Input A** – Select either DUT or REF

SER#1 – Enter a serial number for standard 1, if applicable.

SER#2 – Enter a serial number for standard 2, if applicable.

SER#3 – Enter a serial number for standard 3, if applicable.

* The “

Test By:

” parameter input allows the user to select the type of test – TIME, PULSE,

MANUAL, or ENERGY. If ENERGY is selected, the “

Time:

” parameter input dynamically

changed to “

Energy:

”. This allows a test to be stopped after a pre-set amount of energy has been

accumulated by the D.U.T.

Application 2

Содержание RM-111


































































































Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды

Radian RM-111, Руководство по эксплуатации

Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды