Radian RM-111 Скачать руководство пользователя страница 84

Страница: 84 / 97

RM-111 Operations Manual

Application 10

Application 13

19.0 Interfacing a Solid State Meter to a Test Board
(RM-1P Electronic Light Valve Option)

Equipment Needed:

• RM-111 Automated Comparator

• Meter test board with open collector input

• Solid state meter programmed with a known number of infrared LED calibration
pulses per Kh

• RM-1P Electronic Light valve

• RM-1H or RR -1H Optical Pickup

Test Steps:

1. Install the meter to be tested into the test board socket fi xture.

2. Position the RM-1P between the test board’s light emitter and detector.

• The RM-1P will function with both visible and infrared light.

3. Turn on the RM-111.

4. Select RUN TESTS.

5. Select Pulse Divider.

6. Enter the number of pulses in for one pulse out.

7. Enter the number of pulse input ports (1-3).

8. Select the pulse output type. For this application, choose RM-1P.

Содержание RM-111


































































































Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды

Radian RM-111, Руководство по эксплуатации

Результаты поиска

Содержание RM-111

Отзывы:

Похожие инструкции для RM-111

Бренды по названию

Популярные бренды