manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 5

1-5

VIBXPERT Balancing 11.2010

Introduction

Chapter 1: Introduction

Intended use

VIBXPERT is intended for use as a portable balancing device for the
balancing of 

stationary

 machines equipped 

solely with rotating

components (rotors)

, e.g. turbine rotors, inductors, circulating pumps,

centrifugal compressors, fans, etc. This does not include machines
with oscillating components, e.g. all reciprocating machines.

VIBXPERT can be used without any restrictions  for the balancing of
rigid rotors. Elastic (soft) rotors may only be balanced with VIB-
XPERT at the resonant frequency (±25%) by an experienced user.
The measurement instrument and its accessories may only be
operated by authorized personnel.

PRÜFTECHNIK Condition Monitoring assumes no responsibility for
any damage arising from improper use.

Symbols

Danger to life and limb.

Danger of improper operation which can cause
damage.

Tips on operation as well as important information
about balancing.

NOTE

ATTENTION

WARNING!

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды