manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 34

2-26

VIBXPERT Balancing 11.2010

Setup parameters

This section describes the measurement settings that you generally
can only edit before beginning a balance measurement. The parame-
ters are contained in the 'Setup menu':

- Machine setup (see below)
- Measurement setup (see p. 2-28)
- Transducer setup (see VIBXPERT operating manual, page 2-20)

Machine setup

A 'machine setup' contains the machine data and information on the
measurement setup. VIBXPERT uses these data to calculate a suitable
trial weight and, after each balancing run, the remaining imbalance,
centrifugal force and the attained balancing quality. To create a
machine setup, proceed as follows:

• Mark a rotor type in the selection screen (see p. 2-11).

• Press the MENU button and click on "Task manager".

• Mark the "Machine setup" field.

• Press the MENU button and click on "New" or on "Edit":

P

LANES

: 

One / Two

. Number of balancing planes; cannot be changed

because the rotor type is selected in the selection screen.

C

ORRECTION

 

MODE

*: 

Free / fixed location / fixed weight / meas. tape

;

takes into account restrictions on the machine (fixed locations, e.g.
for ventilator blades) or local circumstances (tape measure).
Depending on the selection, the following parameters can be
selected:

- Number of locations: 3-100. Usually the number of ventilator

blades.

Balancing: Machine setup

*This parameter can be changed in
each balancing run (MENU - Tools)

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды