manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 33

2-25

VIBXPERT Balancing 11.2010

Balancing: Printing

Printing the balancing report

Two different report types are available for documenting the balanc-
ing measurements:

-

Screenshot

: Printout of the current screen

-

Report printouts

: Detailed report printout with general measure-

ment data and balancing-related data.

A report printout can be started from the measurement or data
screen:

Screenshot

:

• Press the MENU button and click on 'Print > Screenshot'.
• Select the printer, press the MENU button and click on 'Print'.

Report printouts:

• Press the MENU button and click on 'Print > 'Report printouts'.
• Check and, if necessary, change the report configuration.
• Select the printer.
• Press the MENU button and click on 'Print'.

The balancing-related report content is found on the 'Measure Info'
tab:
P

OLAR

 

PLOT

: The balancing report contains a polar plot showing the

completed balancing steps.

S

TEP

 

LIST

 

DETAIL

: The balancing report contains all balancing steps

('detailed') or only the first and last steps ('short').

B

ALANCE

 

QUALITY

 / I

MPROVEMENT

: The balancing report contains the

balance quality (setpoint and actual value) if balancing was
performed with the machine setup. If a machine setup was not
used, the improvement in the vibration values is shown in percent.

Details on preparing and configuring a report printout can be
found in the VIBXPERT operating manual (see p. 4-19).

Starting a report printout

Balancing-related report content

Balancing report

Note

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды