manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 12

2-4

VIBXPERT Balancing 11.2010

Diagnosis

Before beginning the balancing procedure, first make sure that the
cause for the adversely affected smooth running of the rotors is
actually an imbalance. Furthermore, a vibration diagnosis indicates
which balancing method is the most suitable.

A series of coordinated measurement tasks are available for the
diagnosis of an imbalance:

•

Click on "Balancing" in the start screen and open the 'Diagnosis'
tab (see below):

Overall value - vibration velocity

Records the broadband vibration of the machine in order to docu-
ment the actual condition before and after balancing. This also makes
it possible to determine the measurement location with the highest
vibration values where the sensors should be mounted (see p. 2-5).

RPM

Measures the rotor RPM. If a machine setup is used for balancing, this
parameter is required in order to calculate the resulting centrifugal
forces.

Phase measurement - one / two planes

Records the amplitude and phase angle of the RPM-synchronous
vibration signal. This allows, for example, the type of imbalance
(static / dynamic) to be determined.

Spectrum & Time waveform - vibration velocity

Measures the FFT spectrum and time waveform. If the 1st harmonic
dominates the spectrum, an imbalance is probably the cause for the
poor running.

Balancing: Introduction

Balancing

'1st Harmonic'

Left:

Diagnosis measurement

Right:

FFT spectrum for diagnosis

 1st RPM harmonic

vibration dominates -> imbalance

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды