manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 10

2-2

VIBXPERT Balancing 11.2010

Two-plane balancing under operat-
ing conditions using an optical
trigger and two vibration transduc-
ers.

Balancing: Introduction

R

R

Clamped weight

Reference mark

Optical trigger

Vibration transducer

If an individual imbalance which does not lie on the center of gravity
is added to a completely balanced rotor in one plane, it is called a
quasi static imbalance. It corresponds to the combination of a static
imblance and a couple imbalance and is usually compensated in two
planes.

Basically, the consideration of whether to carry out balancing in one
or two planes depends on the specific machine situation, i.e. on the
balancing behavior of the rotor and the vibration behavior of the
machine. Simultaneous balancing in two planes is quicker and more
precise than successive balancing measurements in each of two
individual planes. Residual errors that are accumulated in sequential
balancing are therefore prevented. The distance/diameter ratio of the
balancing planes is normally an important decision criterion.

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды