manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 21

2-13

VIBXPERT Balancing 11.2010

Balancing: 1-plane

5. Press the joystick to start the measurement.

6. If the measurement values are stable, press the joystick to stop the

measurement.

7. Switch the machine off.

In the trial run the imbalance should change enough to steadily
reduce the residual imbalance in the subsequent balancing runs. If
the imbalance changes only slightly, increase the trial weight. If the
imbalance has more than doubled, use a smaller trial weight (see the
'Tools' parameter, 'Check bad influence', p. 2-21). If necessary, scroll
back in the data screen of the trial run, change the mass accordingly
and repeat the trial run.

Trim run

1. Move the joystick to the right to close the measurement screen of

the trial run and to open the data screen of the first trim run.
Depending on whether the trial weight resulted in an improvement
or not, it can be left on the rotor or taken off. Respond to the
resulting prompt in the screen accordingly.

2. Attach the recommended mass at the specified position on the

rotor. If necessary, also change the values.

3. Move the joystick to the right until the next measurement screen

appears.

4. Switch on the machine.

5. Press the joystick to start the measurement.

6. If the measurement values are stable, press the joystick to stop the

measurement.

7. Switch off the machine.

Left:

Measure trial run

Right:

Trim run data screen

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды