manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 23

2-15

VIBXPERT Balancing 11.2010

Balancing: 2-plane

Balancing in two planes

In principle, the process here corresponds to the previous section.
Therefore, only the specific features of balancing in two planes are
described in the following section:

Overview of the measurement procedure

Plane A? : Determination of the measurement and balancing plane A.

0.

Initial imbalance: Measurement in plane A and plane B

1A. Trial run: Recommendation for trial weight in plane A;

measurement in plane A and plane B with trial weight in plane A

1B. Trial run: Recommendation for trial weight in plane B;

measurement in plane A and plane B with trial weight in plane B

2.

Balancing run: Recommendation for balancing weight in plane A
and plane B; measurement in plane A and plane B

....

N. Balancing run  ...

Determining the measurement plane & balancing plane A

1. Activate the balancing mode and open the "2 planes" tab.

2. Click on the rotor graphic which corresponds to the rotor type.

3. Select plane A:
- Next connect the transducer which is mounted in measurement

plane A to measurement channel A (see "Overview").

Measuring the initial imbalance in plane A and plane B

1. Switch the machine on and start the initial run.

Measurement plane A

Balancing plane A

Left:

Selection screen - rotor type

Right:

Setting of plane A

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды