manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Руководство по эксплуатации

Поделиться
Скачать
PRÜFTECHNIK VIBXPERT Balancing Скачать руководство пользователя страница 20

2-12

VIBXPERT Balancing 11.2010

First, VIBXPERT records the RPM. The green LED flashes with each
trigger pulse. If the RPM varies too much, a warning message
appears.

Finally, the instrument measures the amplitude and phase of the
RPM synchronous vibration. If the values are unstable, the average is
automatically increased.

3. If the measurement values are stable, press the joystick to stop the

measurement (see previous page).
To repeat the measurement, press the joystick again.

4. Switch the machine off.

Trial run

1. Move the joystick to the right to open the data screen for the trial

run.

2. Enter the mass and fixing angle for the trial weight.

- Click on the mass or angle field under the rotor graphic. The active

field is highlighted in black.

- Enter the respective value in the number editor and confirm the

entry with MENU - 'OK'.

3. Move the joystick to the right until the next screen appears.

If the trial mass is applied at random, there is a risk of increased
imbalance and thus an increased vibration load. Especially if
vibration loads are already very high, this may result in further
machine damage.

4. Switch the machine on.

Balancing: 1-plane

ATTENTION

Left:

Measure 'Initial' run

Right:

Enter mass and angle for trial run

Содержание VIBXPERT Balancing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды