PRONAR T286 Скачать руководство пользователя страница 89

Страница: 89 / 168

SECTION 4

Pronar T286

4.15

4.4

HITCHING AND UNHITCHING THE SECOND TRAILER

A second trailer may only be hitched if it is a machine built on a dual axle chassis and if it

fulfils all the requirements specified in section 1.

Hitching the second trailer to the tractor - trailer unit requires experience in driving an

agricultural tractor with a trailer. While hitching the second trailer, it is recommended to use

the help of another person to guide the tractor driver.

Hitching the second trailer

Position the tractor with the first trailer hitched directly in front of the second

trailer's drawbar.

Immobilise the second trailer with parking brake.

FIGURE 4.6

Rear hitch

(1) hitch body, (2) hitch pin, (3) hitch lifting handle

Raise hitch pin (2) of the first trailer using handle (3) - figure (4.6).

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Похожие инструкции для T286

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Похожие инструкции для T286

Бренды по названию

Популярные бренды