PRONAR T286 Скачать руководство пользователя страница 48

Страница: 48 / 168

Pronar T286

SECTION 3

3.8

FIGURE 3.5

Switching the trailer to "hook trailer" mode

(1) hook frame, (A) "tipper" position (full range), (B) "hook trailer" position (after complete

folding)

"Tipper" or "hook trailer" operation mode of the trailer is selected automatically by means

of slidable telescopic hook frame (1) - figure (3.5) , which shifts the interlock mechanism (6) -

figure (3.4).

The interlock is released when the frame is shifted to position B.

IMPORTANT!

The interlock mechanism can be shifted by moving the hook frame only when the tipping
frame is in the resting position, the rear fender is withdrawn and the slides of the load box
interlock are in folded position.

The trailer is switched to "hook trailer" mode when the hook frame is shifted to position B.
In the whole range, the trailer will work as "tipper".

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды