PRONAR T286 Скачать руководство пользователя страница 133

Страница: 133 / 168

SECTION 5

Pronar T286

5.17

Adjustment of parking brake cable tension

Checking and/or adjustment of parking brake:

•

every 12 months,

•

if needed.

Before commencing the adjustment make certain that the main axle brake is correctly

regulated and is functioning properly.

Hitch trailer to tractor. Park trailer and tractor on level surface.

Place securing chocks under one trailer wheel.

Unscrew the brake mechanism bolt maximally (1) – figure (5.7),

(counterclockwise).

Loosen nuts (7) of clamps (5) of parking brake cable I (2).

Tighten cable and tighten clamps.

Length of parking brake cable (2) should be so selected that at total

release of working and parking brake the cable would be loose and

hanging by approximately 1 - 2 cm compared to fully tensioned cables.

Replacing the parking brake cable

Hitch trailer to tractor. Park trailer and tractor on level surface.

Place securing chocks under one trailer wheel.

Fully unscrew the bolt of the brake crank mechanism (1).

Dismantle shackle (6) at the ends of parking brake cable II (3) (if replacing

cable II (3)).

Loosen nuts (7) of U-bolt clamps (5) on cables being replaced.

If necessary, dismount guide rollers (8).

Remove the pins from lever (4) and from crank mechanism (1).

Dismantle the cable to be replaced.

Clean parking brake components, lubricate parking brake crank mechanism

(1) and pins of cable guide rollers (9).

Install a new cable or cables.

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

PRONAR T286, Руководство оператора, Страница: 133 / 168

Результаты поиска

Содержание T286

Отзывы: