PRONAR T286 Скачать руководство пользователя страница 121

Страница: 121 / 168

SECTION 5

Pronar T286

5.5

5.2.4 CHECK WHEEL AXLE BEARINGS FOR LOOSENESS

FIGURE 5.2

Lifting jack support point

(1) wheel axle, (2) U bolt

Preparation procedures

Hitch trailer to tractor, immobilize tractor with parking brake.

Park tractor and trailer on hard level ground.

Tractor must be placed to drive forward.

Place the wheel chocks under the wheel opposite to the lifted wheel. Ensure

that trailer shall not move during inspection.

DANGER

Before commencing work the user must read the instructions for lifting jack and adhere
to the manufacturer's instructions.

The lifting jack must be stably supported on the ground and so must the axle.

Ensure that trailer shall not move during inspection of axle bearing looseness.

Raise the wheel (opposite to the side where chocks are placed).

The lifting jack should be placed under the axle between U bolts

(2) securing axle (1) to leaf spring - figure (5.2) Recommended

support point is marked with an arrow. Lifting jack must be suited to

weight of trailer.

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды