PRONAR T286 Скачать руководство пользователя страница 63

Страница: 63 / 168

SECTION 3

Pronar T286

3.23

3.2.10 TURNING INTERLOCK HYDRAULIC SYSTEM

The hook trailer is equipped with a passively steered rear steering axle. This solution

facilitates manoeuvring the vehicle, improves stability while driving on turns, reduces

disadvantageous forces in suspension system and chassis which occur while turning.

Consequently, the wear of tyres is reduced and it is easier to drive the tractor with a trailer.

While reversing, the rear axle steering knuckles should be locked. Otherwise, the trailer will

tend to turn in an uncontrolled manner to the left or to the right. The hydraulic system of the

interlock is supplied by the tractor's external hydraulic system through the hydraulic conduits

(2) which are connected to the sockets of a single section of the tractor's hydraulic system by

means of quick couplers (3). The axle is locked by withdrawing or extending the hydraulic

cylinders rods (1). Shock absorber (4) ensures stability of the steering axle and reduces its

excessive vibrations.

FIGURE 3.17

Design and diagram of the hydraulic system of the rear axle turning

interlock

(1) turning interlock cylinder, (2) hydraulic conduit, (3) hydraulic quick coupler, (4) shock

absorber

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды