PRONAR T286 Скачать руководство пользователя страница 162

Страница: 162 / 168

Pronar T286

SECTION 5

5.46

5.13

TROUBLESHOOTING

TABLE 5.10

Troubleshooting

FAULT

CAUSE

REMEDY

Brake system conduits not
connected

Connect brake conduits (applies
to pneumatic systems)

Parking brake applied

Release parking brake.

Damaged pneumatic
system connection conduits

Replace.

Leaking connections.

Tighten, replace washers or seal
sets, replace conduits.

Low pressure in pneumatic
system

Ensure proper pressure in the
system.

Problem with moving off

Control valve or braking
force regulator damaged

Check valve, repair or replace.

Excessive bearing
slackness.

Check play and adjust if needed

Damaged bearings.

Replace bearings.

Noise in axle hubs

Damaged hubs.

Replace.

Poor reliability of braking
system

Insufficient pressure in
system

Check pressure on tractor
pressure gauge, wait till
compressor fills tank to required
pressure.

Damaged air compressor in
tractor Repair or replace.

Damaged brake valve in tractor.
Repair or replace.

Leaking system conduits or
connections. Check system for
tightness.

Incorrect main or parking
brake adjustment.

Regulate setting of expander arms
or tension of parking brake cable

Excessive heating of axle
hubs

Worn brake linings.

Change brake shoes

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды