PRONAR T286 Скачать руководство пользователя страница 124

Страница: 124 / 168

Pronar T286

SECTION 5

5.8

Secure castellated nut with cotter pin and mount hub cap.

Delicately tap hub cap with rubber or wooden hammer.

The wheel should turn smoothly without stiffness or detectable resistance not originating from

abrasion of brake shoes in brake drum. Adjustment of bearing slackness may only be

conducted when the trailer is hitched to tractor and the load box is empty.

TIP

If the wheel is dismounted, bearing slackness is easy to check and adjust.

5.2.6 MOUNTING AND DISMOUNTING WHEEL, INSPECTION OF WHEEL NUT

TIGHTENING.

Wheel removal

Immobilise trailer with parking brake.

Place the wheel chocks under the wheel opposite to the dismantled wheel.

Ensure that trailer shall not move during wheel dismounting.

Loosen wheel nuts according to sequence given in figure (5.4).

Place a lifting jack and raise the trailer to a sufficient height so that the wheel

to be replaced does not touch the ground.

The lifting jack should have sufficient lifting capacity and should be

technically reliable.

The lifting jack must be positioned on a level and hard surface so as to

prevent sinking into the ground or relocating the jack during lifting.

If necessary, use proper backing plates in order to reduce unit

pressure of the jack's base on the ground and prevent its sinking into

the ground.

Dismount wheel.

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды