PRONAR T286 Скачать руководство пользователя страница 125

Страница: 125 / 168

SECTION 5

Pronar T286

5.9

Wheel installation

Clean axle pins and nuts of dirt contamination.

Do not grease thread of nuts and pins.

Check condition of pins and nuts, if necessary replace.

Place wheel on hub, tighten nuts so that wheel rim tightly fits the hub.

Lower trailer, tighten nuts according to recommended torque and given

sequence.

TIP

Wheel nuts should be tightened using a torque of 450 Nm - nuts M22x1.5.

Tightening nuts

Nuts should be tightened gradually diagonally, (in several stages, until obtaining the required

tightening torque) using a torque spanner. If a torque spanner is not available, one may use

an ordinary spanner. The arm of the spanner (L) figure (5.4) should be selected according to

the weight of the person (F) tightening the nut. Remember that this method of tightening is

not as accurate as the use of a torque spanner.

FIGURE 5.4

Sequence of tightening nuts, axles with 10 M22x1.5 pins

(1) - (10) sequence of nut tightening, (L) spanner length, (F) user weight

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

PRONAR T286, Руководство оператора, Страница: 125 / 168

Результаты поиска

Содержание T286

Отзывы: