PRONAR T286 Скачать руководство пользователя страница 94

Страница: 94 / 168

SECTION 4

Pronar T286

4.20

Fold the rear bumper

Press and hold the push-button for folding

the rear fender. After folding the fender,

indicator light (4) must light up on the control

panel - figure (4.7).

If the fender is not completely withdrawn, the

tipping function does not work.

Place the tractor and the trailer in front of the load box, in the straight line, at a

distance of about 1 meter from the load box hitch.

Withdraw

the

load

box

interlock (if it is extended).

Press

and

hold

the

push-button

for

withdrawing the load box interlock. Indicator

light (15) must light up - figure (4.7).

Set the trailer to "hook trailer"

function.

Shift the hook frame maximally to the rear by

pressing the push-button for withdrawing the

hook frame. If the trailer is correctly set to

"hook trailer" function, indicator light (10) will

light up - figure (4.7).

Содержание T286









































































































































































Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T286, Руководство оператора

Результаты поиска

Содержание T286

Отзывы:

Бренды по названию

Популярные бренды