ProLinx 6202-WA-DFNT-DFCM3 Скачать руководство пользователя

Страница: 76 / 190

6202-WA-DFNT-DFCM3

♦

ProLinx Gateway

Diagnostics and Troubleshooting

Wireless EtherNet/IP to DF1 Master/Slave-3 ports

Page 76 of 190

ProSoft Technology, Inc.

February 2, 2009

Viewing Radio Configuration

Press

[C]

to view radio configuration. Use this command to view the port type,

channel, data length and other radio configuration settings.

Viewing Radio Status

Press

[S]

to view the current operational status of the radio. Use this command

to view connection and signal status, packets and bytes transferred, signal
quality and errors.

Continuously Monitoring Radio Status

Press

[1]

to monitor radio status continuously. Use this command to view the

signal strength and noise level for the radio in real time.

Important:

When in continuous radio monitor mode, program execution will slow down. Only use

this tool during a trouble-shooting session. Before disconnecting from the Config/Debug port,
please be sure to press a key to disable the radio status monitor. This action will allow the module
to resume its normal operating mode.

Returning to the Main Menu

Press

[M]

to return to the Main Menu.

Содержание 6202-WA-DFNT-DFCM3































































































































































































Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды

ProLinx 6202-WA-DFNT-DFCM3, Руководство пользователя

Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды