ProLinx 6202-WA-DFNT-DFCM3 Скачать руководство пользователя

Страница: 53 / 190

Configure the Module

6202-WA-DFNT-DFCM3

♦

ProLinx Gateway

Wireless EtherNet/IP to DF1 Master/Slave-3 ports

ProSoft Technology, Inc.

Page 53 of 190

February 2, 2009

2.5.13 Radio Ethernet Configuration (WATTCP)

The Radio Ethernet Configuration is used to configure ethernet and wireless
communication information.

Radio_IP

Default: 192.168.0.100

The IP address of the module to be used in wireless communication.

Radio_Subnet_Mask

Default: 255.255.255.0

The subnet mask to be used in wireless communication.

Radio_Default_Gateway

Default: 172.16.10.1

The default gateway to be used in wireless communication.

Ethernet Settings

Important:

The settings for my_ip, netmask, gateway and Local_Domain_Name are only

applicable for modules equipped with an Ethernet port. If you are configuring a module without an
Ethernet port, you may disregard these settings as they are not used.

my_ip

Default: 192.168.0.100

The IP address for the module. Each word contains one of the four values that
comprise the IP address.

Содержание 6202-WA-DFNT-DFCM3































































































































































































Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды

ProLinx 6202-WA-DFNT-DFCM3, Руководство пользователя

Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды