ProLinx 6202-WA-DFNT-DFCM3 Скачать руководство пользователя

Страница: 40 / 190

6202-WA-DFNT-DFCM3

♦

ProLinx Gateway

Configure the Module

Wireless EtherNet/IP to DF1 Master/Slave-3 ports

Page 40 of 190

ProSoft Technology, Inc.

February 2, 2009

Wired DF1 Pass-Through in Infrastructure mode

[Radio DF1 Pass-Through Server]

Enabled : Yes # Y=Use server, N=Do not use server

Service Port Number : 15000 # TCP service port for this server

Busy Timeout : 500 # Time to wait for not Busy (100-65535 mSec)

Note:

This section of the configuration file is applicable to third party port re-routing software that

can RSLinx serial port driver to an IP address port. When such software is not necessary then this
section is ignored by the module.

[DF1 Pass-Through Port]

Enabled : Yes # Y=Use port, N=Do not use port

Request Timeout : 1000 # Request messgage timeout (0-65535 mSec)

Busy Timeou t : 500 # Port Busy timeout (0-65535 mSec)

ACK Timeout : 100 # DLE-ACK timeout (0-65535 mSec)

[DF1 Port 1]

Enabled : Yes # Y=Use port, N=Do not use port

RS Interface : RS-232 # 0=RS-232, 1=RS-485, 2=RS-422

Type : Master # M=Master, S=Slave

Local Station ID : 0 # DF1 node address

Protocol : Full-Duplex # F=Full-Duplex, H=Half-Duplex

Termination Type : CRC # B=BCC, C=CRC

Baud Rate : 38400 # Baud rate for Port 210-38400

Parity : None # N=None,O=Odd,E=Even,M=Mark,S=Space

Data Bits : 8 # 5, 6, 7 or 8

Stop Bits : 1 # 1 or 2

Min Response Delay : 0 # 0-65535 mSec before sending response msg

RTS On : 0 # 0-65536 mSec before message

RTS Off : 1 # 0-65536 mSec after message

Use CTS Line : No # Use CTS modem control line (Y/N)

Response Timeout : 1000 # Response messgage timeout (0-65535 mSec)

Retry Count : 3 # Response failure retry count

ENQ Delay : 10 # 0-65535 mSec before DLE-ENQ sent

Minimum Command Delay: 10 # Minimum number of msec's between commands

Error Delay Counter : 100 # 0-65535 Command cycle count if error

Command Control Reg : -1 # Cmd control start DB Reg (-1=ignore)

First File : 7 # First file number for SLC simulation

File Size : 200 # Number of elements in each file

File Offset : 0 # Database offset for first file element

Содержание 6202-WA-DFNT-DFCM3































































































































































































Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды

ProLinx 6202-WA-DFNT-DFCM3, Руководство пользователя

Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды