ProLinx 6202-WA-DFNT-DFCM3 Скачать руководство пользователя

Страница: 165 / 190

Reference 6202-WA-DFNT-DFCM3

♦

ProLinx Gateway

Wireless EtherNet/IP to DF1 Master/Slave-3 ports

ProSoft Technology, Inc.

Page 165 of 190

February 2, 2009

Code (Int)

Code (Hex) Description

-4074

0xF016

Scanner not able to communicate with 1771 rack adapter

-4073 0xF017

Type

mismatch

-4072

0xF018

1171 module response was not valid

-4071 0xF019

Duplicate

label

-4070

0xF01A

File is open; another node owns it

-4069

0xF01B

Another node is the program owner

-4068 0xF01C

Reserved

-4067 0xF01D

Reserved

-4066

0xF01E

Data table element protection violation

-4065

0xF01F

Temporary internal problem

Module Specific Error (not DFNT Compliant)

Code (Int)

Code (Hex) Description

-1

0xFFFF

CTS modem control line not set before transmit

-2

0xFFFE

Timeout while transmitting message

-10

0xFFF6

Timeout waiting for DLE-ACK after request

-11

0xFFF5

Timeout waiting for response after request

-12

0xFFF4

Reply data does not match requested byte count

-20

0xFFEC

DLE-NAK received after request

-21

0xFFEB

DLE-NAK sent after response

5.8.3 DF1 Configuration Error Word

DF1 Configuration Error Word errors are stored in protocol-specific registers. The
following table lists the Port/Register Address configuration.

DF1 Port

Configuration Error Word Register

0 6307

1 6707

2 7107

3 7507

A register containing a code indicates a problem with the configuration. The
following table lists the codes, a description of the problem, and parameters to
correct the error condition within the configuration file.

Bit Code

Description

0x0001

Invalid Enabled parameter (Yes or No)

0x0002

Invalid RS-Interface parameter (0 to 2)

0x0004

Invalid Type (Master or Slave)

0x0008

Invalid Protocol (RTU or ASCII)

0x0010

Invalid Baud Rate

0x0020

Invalid Parity (None, Odd, Even)

0x0040

Invalid Data Bits (7 or 8 bits)

0x0080

Invalid Stop Bits (1 or 2)

0x0100

Invalid Use CTS Line (Yes or No)

0x0200

Retry Count Invalid (0 to 10)

Содержание 6202-WA-DFNT-DFCM3































































































































































































Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды

ProLinx 6202-WA-DFNT-DFCM3, Руководство пользователя

Результаты поиска

Содержание 6202-WA-DFNT-DFCM3

Отзывы:

Похожие инструкции для 6202-WA-DFNT-DFCM3

Бренды по названию

Популярные бренды