background image

6202-WA-DFNT-DFCM3 

 ProLinx Gateway 

Support, Service & Warranty 

Wireless EtherNet/IP to DF1 Master/Slave-3 ports  

 

Page 184 of 190  

ProSoft Technology, Inc. 

February 2, 2009 

 

e)  Customer agrees that it shall not, and shall not authorize others to, copy 

software provided by ProSoft (except as expressly permitted in any 
license agreement accompanying such software); transfer software to a 
third party separately from the Product; modify, alter, translate, decode, 
decompile, disassemble, reverse-engineer or otherwise attempt to derive 
the source code of the software or create derivative works based on the 
software; export the software or underlying technology in contravention of 
applicable US and international export laws and regulations; or use the 
software other than as authorized in connection with use of Product. 

f) 

Additional Restrictions Relating To Software And Other Intellectual 
Property

 

In addition to compliance with the Terms of this Warranty, Customers 
purchasing software or other intellectual property shall comply with any 
license agreement accompanying such software or other intellectual 
property. Failure to do so may void this Warranty with respect to such 
software and/or other intellectual property. 

6.3.5 Disclaimer 

of 

all Other Warranties 

The Warranty set forth in What Is Covered By This Warranty (page 182) are in 
lieu of all other warranties, express or implied, including but not limited to the 
implied warranties of merchantability and fitness for a particular purpose. 

6.3.6  Limitation of Remedies ** 

In no event will ProSoft or its Dealer be liable for any special, incidental or 
consequential damages based on breach of warranty, breach of contract, 
negligence, strict tort or any other legal theory. Damages that ProSoft or its 
Dealer will not be responsible for included, but are not limited to: Loss of profits; 
loss of savings or revenue; loss of use of the product or any associated 
equipment; loss of data; cost of capital; cost of any substitute equipment, 
facilities, or services; downtime; the claims of third parties including, customers of 
the Purchaser; and, injury to property. 

** Some areas do not allow time limitations on an implied warranty, or allow the exclusion or 
limitation of incidental or consequential damages. In such areas, the above limitations may not 
apply. This Warranty gives you specific legal rights, and you may also have other rights which vary 
from place to place. 

6.3.7  Time Limit for Bringing Suit 

Any action for breach of warranty must be commenced within 39 months 
following shipment of the Product. 

Содержание 6202-WA-DFNT-DFCM3































































































































































































Отзывы: