PowerBoss commander t82 europe Скачать руководство пользователя страница 86

Страница: 86 / 96

Commander T Series PB# 4100032

Rev.C 03/12

Page 86

TROUBLESHOOTING CHART

PROBLEM

POSSIBLE CAUSE(S)

SOLUTION(S)

Engine overheats.

NOTE: If coolant loss has not

occurred, check for malfunction

of the temperature sending unit.

Low coolant level.

Supply coolant.

Fan blade installed incorrect

Reinstall (pusher type fan)

Clogged radiator.

Flush radiator.

Loose fan belt.

Tighten belt.

Defective thermostat.

Replace thermostat.

PowerBoss® moves slowly

or does not move.

Parking brake is on.

Release brake.

Directional control pedal jammed, damaged, or

not adjusted properly.

Clear jam or adjust linkage.

Tow valve in tow position

Move to drive position

Low hydraulic fluid level.

Add hydraulic fluid.

Hydraulic fluid temperature too high and too

thin caused by excessive load, climbing, high

environment temperatures, worn pump, or

improper fluid.

Use the proper weight oil for the

operation conditions; check pump.

Hayes coupler failed

Replace

Other problems with the hydraulics system:

pump failure, motor failure, relief valve leaking

or stuck open.

See Hydraulics System

Problems in this section.

Tow Valve improperly set.

Turn to correct position.

TROUBLESHOOTING

Содержание commander t82 europe






























































































Результаты поиска

Содержание commander t82 europe

Отзывы:

Похожие инструкции для commander t82 europe

Бренды по названию

Популярные бренды

PowerBoss commander t82 europe, Руководство пользователя

Результаты поиска

Содержание commander t82 europe

Отзывы:

Похожие инструкции для commander t82 europe

Бренды по названию

Популярные бренды